ArmorUltra Industrial Coating System

Now Available Military Grade 2-Part Floor Epoxy for Industrial Coating!

Armorpoxy now offers ArmorUltra, a 2-part ultra heavy-duty quick drying commercial/industrial grade clear floor epoxy. This unique industrial coating product contains 100% solids and dries in 24 hours. Ideal for locations where 'down time' needs to be minimized and for the most demanding floor applications where the longer life can justify higher material costs. It is for use on concrete floors only.

Armorpoxy industrial coating can be used for minor floor leveling and repair of minor cracks and fissures. For expansion joints and other cracks see our Online Store for crack fillers. Ultra-fast drying and curing. Ideal for auto repair facilities, warehouses, restaurants, kitchens, hangers, equipment rooms, battery rooms and other industrial and commercial and high-use residential applications. Designed for indoor use only. ArmorUltra is not UV stabilized for outdoor uses. For UV protection and maximum staining and chemical resistance, use our UV 2-part Polyurethane Top Coat. This industrial coating product is highly resistant to acids, alkalies, solvents, fuels, and other chemicals.

ArmorUltra is mixed at the jobsite at a 2:1 ratio. Available in 3 gal 'kits' (2 gals of A & 1 gal of B) which will cover up to 375 square feet @ 12 mils and 15 gal 'kits' (10 gals of A & 5 gals of B) which will cover up to 1875 square feet @ 12 mils. Single coat application should be installed @ 12-20 mils and yield 120-130 sq. ft./gallon. Thicker applications may yield significantly less coverage, while thinner applications will yield more coverage. Visit our BUY NOW page for prices or to order now!

ArmorUltra industrial coating product is available in clear and 9 other colors (Dark Gray, Medium Gray, Light Gray, Tile Red, Beige, Yellow, Off White, White and Navy Blue. We also offer ArmorUltra in a low temp formulation for application in colder temperatures. Call for details.

For non skid areas we offer a non skid additive 60 or 30 grit. To use the non skid additive apply the first coat and then either by hand or by use of a fertilizer spinner apply the grit to the floor. A second coat is required to hold the grit in place and assure long life. Non skid is sold in a 10 lb container for $59.99 and will treat about 10 gals.

ArmorUltra can only be applied to bare concrete or over existing 100% solids epoxies. If you are unsure as to the present floor coating, then it must be removed by shot blasting. Use magnetic broom and vacuuming to remove any shot prior to applying ArmorUltra. Test of moisture by applying a 3' x 5' sheet of clear plastic to floor area. Duct tape all 4 sides. Wait 24 hours. If moisture appears then do not apply.

Application of this industrial coating product is as follows: Sweep floor. Clean floor by power washing. Muriatic acid etch if possible and then rinse well to neutralize the acid. Oil stains must be removed or treated prior to application. See our online store/cleaners page for special products to remove oil and grease. Mix parts A & B for 3 minutes using a power drill mounted paint mixer. Make sure to have all of your tools and supplies on hand and be 'ready to go' as ArmorUltra has a relatively short "pot life". Pot life is the amount of time before the ArmorUltra starts to thicken and is approximatley 30 minutes at 75 degrees and 90 minutes at 60 degrees. Make sure to not overmix if you cannot apply that same quantity of ArmorUltra before it starts to thicken. Recommended application method is by pouring a 'bead' of the mixed material onto the floor and squeegeeing out with a 18-24" flat rubber squegee. A 1/4" nap roller can be used to get into difficult areas or under equipment. A second coat can be applied after 24 hours. Backrolling with 1/4" nap roller after squeegeeing is highly recommended.

Coverage can be adjusted up/down by applying thicker/thinner. Coverage @ 12 mils is 130 square feet/gallon and can be applied up to 30 mils thick for a coverage of 53 square feet/gallon. Thicker coverage can be obtained by the use of a notched squeegee instead of a roller. Notch sizes of 1/16" - ¼" can be used. The larger the notch size, the thicker the application. Max recommended final thickness is 35 mils. Entire product batch does not need to be mixed at the same time…as long as the ratio of 2:1 is adhered to opened non-mixed containers can be used in the future.

Click to buy our industrial coating product