ARMORPOXY BOTTOM PAINT
Epoxy Bottom Coating for Your Boat
Our high performance bottom paint has the highest legally allowable amount of ablative copper. Self-cleaning while underwater. Simply clean your hull, and apply. Addition of second coat adds significant life. Available in two versions, standard grade 45% copper and ultra high performance 67% copper.
BOTTOM PAINT APPLICATION TIPS
Surface Preparation: For applying boat paint the surface must always be clean, dry and properly prepared prior to painting. Failure to do so will lead to eventually blistering and/or peeling. All sanded surfaces must be wiped clean with Dewaxer - 973 to remove sanding residue before the first coat of boat paint is applied.
General Application: For use on boats below the true waterline. Boat paint can be brushed or rolled on fiberglass, wood, steel and previously painted surfaces per application systems below. Do not use boat paints on aluminum. Apply at least 3 coats of paint for best performance, as the life of the boat paint is proportional to the number of coats applied.
Mixing and Thinning: Shake or mix thoroughly and stir continuously while using. Thin when necessary with Reducer - 974.
Theoretical Coverage: Depending on surface conditions, one gallon of bottom boat paint will usually cover over 400 square feet of surface when brushed or rolled.
Estimated Dry Times: Bottom boat paints are designed for overcoating after an overnight dry. Prior to launching, allow a minimum dry of overnight. If drying conditions are poor, or if paint was applied too thick, longer periods of drying will be required. Fresh coats of paint must be thoroughly dry before overcoating.
Yearly Repainting: Scrub bottom clean at haul-out. Repaint only if old boat paint is sound and tight; if not, remove it by sanding or with paint remover. If old boat paint is rough, sand it with 100-150 grit sandpaper. Prepare seams, nicks and chips as below. Spotcoat any scuffs with antifoulant. Apply 3 coats of antifoulant.
On Bare Wood: If seams are not flush, fill them with seam compound. Dry several days until skin forms. Do not sand. Fill nicks with trowel cement, dry hard, sand, apply antifoulant (reduced 10%) then follow with 2 additional unreduced coats of antifoulant.
On Bare Fiberglass: Dewax by washing with Dewaxer_-_973, remove dissolved wax at once with clean paper towels or rags; repeat; sand hard to a dull finish with 80-100 grit sandpaper. Fill any chips with trowel cement, dry hard, sand. Apply 5 coats of 8000A / 8000B Bottom Protect High Build Epoxy Primer, then apply 3 coats of antifoulant.
On Bare Steel: Sandblast surface to a near white metal; remove blast residue with a broom and airhose. Wipe off with Dewaxer - 973. Do not sand. Fill in any imperfections with fairing compound. Sand smooth and wipe clean. Apply 5 coats of 8000A / 8000B Bottom Protect High Build Epoxy Primer, then apply 3 coats of antifoulant.
COPPER PRO™ 67
Self Polishing Ablative
Single Season
No Paint Buildup
Eliminates Heavy Sanding
Tremendous Protection for Extreme Fouling Conditions
Copper Pro™ 67 provides antifouling protection against barnacles, algae and hydroids in salt and fresh water on boat bottoms only. Its ablative copolymer base renders a smooth finish with durability and abrasion resistance. Copper Pro 67 releases biocide by the constant exposure of new paint film to the water. Copper Pro 67 has universal application over all types of properly prepared bottom paints (except aluminum). For use on fast fiberglass boats, as well as wood and steel hulls.
COPPER SHIELD™ 45
Self Polishing Ablative
Single Season
No Paint Buildup
Eliminates Heavy Sanding
Good Protection for Moderate Fouling Conditions
Copper Shield™ 45 provides antifouling protection against barnacles, algae and hydroids in salt and fresh water on boat bottoms only. Its ablative copolymer base renders a smooth finish with durability and abrasion resistance. Copper Shield™ 45 releases biocide by the constant exposure of new paint film to the water. Copper Shield™ 45 has universal application over all types of properly prepared bottom paints (except aluminum). For use on fast fiberglass boats, as well as wood and steel hulls.
