ARMORPOXY POOL PAINT
Armorpoxy is dedicated to providing the finest swimming pool paint to residential and commercial pool owners. We offer both 1-part epoxy fortified and 2-part epoxy pool paints for the beautification, restoration, and protection of concrete, plaster, fiberglass, and previously painted swimming pools. 5 year warranty! FAST SAME DAY SHIPPING!
ArmorPoxy Pool 1-part epoxy fortified PREMIUM coating designed for maximum protection against UV rays and chlorine for new and old concrete pools Longest lasting protection against fade. Armorpoxy is used over other chlorinated rubber pool paints in good condition, as well as bare concrete and plaster surfaces for pool repair and maintenance. Dries quickly, durable, and resists fading, chemicals and abrasion. Warranty covers fading, blistering. Armorpoxy 1-part is similar to a ‘chlorinated rubber’ type paint, but much higher performance.
ARMORPOXY 2 PART POOL COATING. Rated ‘Best’ by leading pool magazine testing! Armorpoxy’s 2-part premium epoxy pool paint high build coating gives maximum protection, as well as having fill qualities for imperfect pool surfaces. Epoxy pool paint is designed for maximum protection against blistering UV rays, chlorine, algae growth, and extreme temperatures variations. Used by thousands of recreation departments throughout the country. It is also efficiently used for pool repair against signs of wear and tear. Longest lasting against fade. Can be applied over most types of epoxy pool coatings, as well as bare concrete, gunite, plaster, and marcite; also perfect for whirpools, jacuzzis and spas. Dries quickly, durable and resists chipping, chalking and abrasions.
Estimating the amount needed:
Most common pools that have shallow/deep ends:
Length x width = Base Footage. Base Footage x 1.7 = actual square footage. Multiply by 2 (for two coats needed) = Actual Square Footage.
Divide by 300 for gallons needed. Remember that the 2-part pool paint comes in 2 gallon ’sets’ so order 1/2 the amount of sets that you need gallons for.
Example: 20 x 40 pool
20 x 40 = 800, 800 x 1.7 = 1,360 sq ft. 1360 x 2 (coats) = 2,720. 2,720 / 300 = 9 gals. So you would order 9 gallons of 1 part, 5 kits of 2 part.
FINISH: Gloss
Colors: Sky Blue, Royal Blue, Aqua, Medium Blue, Red, Black, Yellow, White
SOLVENT TYPE: Hi FLash Naphtha, Mineral Spirits, Xylene (2 part)
VOC: 4.5 lbs./gal. (540 grams/liter)
SOLIDS BY WEIGHT: 60%
WEIGHT PER GALLON: 11 lbs. per gallon (varies by color)
RECOMMENDED DRY FILM: 4.0 mils
COVERAGE: Practical coverage at two mils dry is 300 square feet per gallon on smooth surfaces. Recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough, or sandblasted surfaces.
VISCOSITY AT 75°F (24°C): 70-80 KU
AVERAGE DRY TIME 75°F: Dries to the touch in 30 minutes. Lower temperatures & higher humidity will slow down dry times. Recoat in 24 hours. Allow 5 days for complete cure before filling pool with water. Add 1 day dry time for each day of heavy humidity or rainy conditions.
RECOMMENDED REDUCER: Hi Flash Naphtha
RESISTANCE TO: Alkali, Algae, Mineral Oils, Fresh and Salt Water
RECOMMENDED PRIMERS: Self Priming, non required
APPLICATION: Brush, Spray or Roller (preferred)
Roll: 3/8″ nap roller. Keep roller wet. Roll in one direction, rewet, then cross roll.
Spray: Conventional Air 50-70 psi, Tip Size .055-.070, Airless 2200-2500 psi, Tip Size .019-.023.
POT LIFE: Not Applicable for 1-part ArmorPool. For 2-part pool paint 2-3 hours.
LIMITATIONS: Do not apply epoxy pool paint if material, substrate, or ambient temperature is below 50°F or above 95°F. NOT FOR VINYL LINED OR METAL POOLS. (2 part epoxy is suitable for steel pools.)
SHELF LIFE: Minimum 12 months depending on storage conditions.
MIXING: Mechanically mix well for 10 minutes, apply as it comes from the container, and thin as needed for proper performance.
PACKAGE: 1 Gallon cans, 5 Gallon pails. 2-part epoxy sold in 2 or 10 gallon kits.
